What is the correct procedure for nail polish nail art?

Modification

First use a standard file to trim the nail to the designed shape, and then pay attention to the nail tip to remove and clean the finger debris with a sponge file to prevent the nail polish glue from sticking to the finger debris and causing the nail tip to quickly rise and fall off. Trimming the dead skin: first push the excess dead skin on the edge of the nail with a dead skin steel pusher, and then trim it with dead skin scissors to prevent the nail polish gel from sticking to the dead skin or meat and causing the trailing edge to quickly rise and fall off. Carve and polish the nail surface: Then use a sponge to rub the rough surface to carve the surface of the nail, focusing on the edge of the nail and the tip of the nail. If you encounter a nail that falls off or is thin, you must use a standard file to roughen it carefully. Note: This step can be completed quickly without affecting the quality. Because: in addition to repairing, carving and polishing the nail surface, it needs to be handled carefully. Finger scraps can be cleaned up with a single stroke (repair of dead skin, some girls have less glial dead skin on the nail margin, so you can do a simple repair or no repair, just gently push the dead skin up. You can proceed to the next step. When cleaning finger debris, you can also lightly touch it when repairing.

platinum gel nail

Apply bonding Binder.

The correct operation process of nail polish  ,The binder is a water-like body, so don’t take too much to avoid running or not drying. The bonding binder only needs to be applied to the periphery of the nail and the tip of the nail, because the focus is on the periphery and the tip of the nail, which is also the part that is easy to fall off. When removing the nails, the first one is easier to remove. The second one will not cause damage to the surface of the customer’s nails. Finally, pay attention to the edge of the nail, and no light is needed. Note: This step can be omitted if the speed is increased. Because some brands of adhesive and primer are two-to-one, you can apply only the primer.

Christmas glitter gel polish wholesaler

Apply primer/base coat

The correct operation process of gel nail polish : The amount of base coat should be full. Don’t spread too thin around the edges. If it is too thin, it will lose support and cause the edges to break and fall off like pancakes. It is recommended to use one-half smearing method, from bottom to top (first apply the lower half of the nail and then apply the entire face up, so that the color saturation is stronger and more even up and down), and finally pay attention to the wrapping. The LED lighting must be 1 minute , UV light must be 3 minutes. (Even lighting)

Apply nail polish

The correct operation process of the nail polish . The nail polish is applied normally and the amount is normal. It does not need to be too much. If there is too much, uneven application will occur. Also, pile up a little more around the edges, so that the edges will not be blurred or faint, and will be firmer. So as not to fall off in lumps. Finally, pay attention to the edging, LED light for 30 seconds, UV light for 1 minute. (Evenly illuminate the light) Then apply the same as above for a second time, the color saturation will be enhanced.

supply Christmas red platinum gel polish

Smear top coat

The correct operation process of the nail polish gel, The amount of the sealing layer is full, the edge should not be applied too thin, and completely cover the color gel, apply the nail surface, and finally pay attention to the edge. The LED light must be 1 minute, and the UV light must be 3 minutes. (Evenly illuminate the light) Also remember that if the customer’s nails are thin, it is recommended to apply the primer 3 times to reinforce it and then apply the colored glue, never apply more sealant

1. After reinforcement, it has supporting force and is not easy to fall.

2. If you apply the sealing layer 3 times, it will be very troublesome to remove it, because the density of the primer of all nail polishes is not as high as that of the sealing layer, so the primer is easy to remove. The above is the standard operating procedure for nail polish.

For business ,please contact :

 info@newcolorbeauty.com Whatsapp:0086 136 6298 7261

nail Gel wholesaler


Post time: Jun-04-2021

Newsletter Stay tuned for Updates

Send